Author Topic: Chatham Dockyard South Dock Complex  (Read 163 times)

Offline Signals99

  • New Member
  • *
  • Posts: 10
Re: Chatham Dockyard South Dock Complex
« Reply #5 on: March 01, 2021, 12:30:18 AM »
Thanks Stuart,the years I worked in the yard I never realy understood that system,as a HP monitor we were almost the first down the dock bottom to check for "hots spots" on the Nuclear boats,remember being fascinated by all the fish splashing about in the remaining water,some REALY big ons too,one of our guys got bitten by a very long eel type fish when we beded Dreabnought down for her final it must be said some of those boats were really humming ,especially round the "over board discharge valve"area it was our job to place plastic coverd lead sheets to shield the radiation hot spots Untill such time as a proper controld area could be established on the dock bottom,once the AC/RC system was hooked up then  &. Only then were any other personal permitted on the dock bottom

Offline MartinR

  • Hero Member
  • *****
  • Posts: 670
Re: Chatham Dockyard South Dock Complex
« Reply #4 on: February 28, 2021, 11:23:00 PM »
Thanks Stuart.  I'd always assumed that the tide was the main factor in filling and emptying, with over 5m at springs it would have been criminal not to use it.

Offline stuartwaters

  • Administrator
  • Hero Member
  • *****
  • Posts: 685
Re: Chatham Dockyard South Dock Complex
« Reply #3 on: February 28, 2021, 06:19:44 PM »
In a word, yes. The pumps could be bypassed by allowing the docks to drain through the filling culverts.


The dock would normally be kept dry and prior to a ship going in, the tie-rods securing the Caisson to the bottom of the dock were removed. Immediately before the ship was due to go in, the penstock valves on the filling culverts would be opened at the low water before. As the tide came in, the dock would flood. Once there was enough water to float the Caisson, the shore-side air compressor would be connected and the ballast tank would be blown. This would make the Caisson float up and once disconnected from the shore-side air compressor, it would be towed out by a tug and secured to a buoy in the river.


The ship would then be manoeuvred into the dock by a combination of tugs and shoreside capstans. Once it was centred in the dock, the tug would push the Caisson back into place, the ballast tanks would be vented and it would sink and be secured with large wedges hammered in from the top.


Once the tide started to ebb, the water level in the dock would fall along with the level of the river outside. A diver would be sent into the dock to measure the distance between the keel of the ship and the stalls on the bottom of the dock. When the ship's keel touched the stalls, the diver would give the signal and the penstocks would be closed. The dockside cranes would then be used to put the shoring into place and the shores would be secured in place with wedges hammered in. Once the shores were secure, the penstocks would be opened again to allow the remaining water to drain from the dock. The pumps would be used to pump out the rest of the water if the tide wasn't going to fall far enough to completely drain the dock.


Once the dock was completely drained, the Caisson would be secured with tie-rods to the bottom of the dock and the inevitable gap between the Caisson and the dock mouth would be caulked.


If the timings of the tide were not right or if they were in a hurry to get the ship docked, the pumps would be used to drain the docks instead of allowing them to drain with the tide.


This procedure was only used for Dry Docks 2 - 4. The other Dry Docks opened out into the No 1 Basin and they were always pumped out.
"I did not say the French would not come, I said they will not come by sea" - Admiral Sir John Jervis, 1st Earl St Vincent.

Offline MartinR

  • Hero Member
  • *****
  • Posts: 670
Re: Chatham Dockyard South Dock Complex
« Reply #2 on: February 28, 2021, 04:41:27 PM »
Did the pumps allow free-flow when the tide was out?  I noticed the tidal flaps, I assume they are similar to the ones seen on storm drains which are effectively one-way vales.

Offline stuartwaters

  • Administrator
  • Hero Member
  • *****
  • Posts: 685
Chatham Dockyard South Dock Complex
« Reply #1 on: February 28, 2021, 04:32:00 PM »
This is a diagram I made from original plans of the system of culverts, tidal flaps, valves etc for the South Dock Complex at Chatham. This is Dry Docks 2 - 4. I found the plans while having a clearout when I worked in the Chatham Historic Dockyard.


"I did not say the French would not come, I said they will not come by sea" - Admiral Sir John Jervis, 1st Earl St Vincent.